Thank you for your interest in our equipment for sale.

If you are interested in any of the equipment listed below, please contact Rick Griffin at (203) 269-0557 X25 for greater detail and/or to schedule a visit to see the equipment.

1999 Fadal VMC 4020 AHT Model 917-1 $48,800

Fadal 4020 AHT model 917-1 vertical machining center. Complete rebuild/calibration March 2008. 21-position ATC. Cat 40 taper. X-travel 40″; Y and Z travel 20″. Spindle nose to table 4″-24″.

For more information, please contact us

1996 Fadal VMC 4020 HT Model 906-1 $42,800

Fadal 4020 HT model 906-1 vertical machining center. Complete rebuild/calibration March 2008. 21-position ATC. Cat 40 taper. X-travel 40″; Y and Z travel 20″. Main spindle nose to table 4″-24″ A-axis board installed (A-axis spindle is not included in sale).

For more information, please contact us

Federal 45-ton OBI press $8,000

Federal 45-ton OBI press. Air clutch/brake. 2″ stroke; 9-1/8″ shut height. 2-1/2″ x 18″ x 35″ bolster with 6 x 20″ opening. 13″ x 18″ ram. Reeves Vari-Drive. Palm buttons. Set up for pull-backs. Ram knock-out slot.

For more information, please contact us

Perkins 450-B 35-ton OBI press $9,000

Perkins 450-B 35-ton OBI press Asset Description Notes: Perkins 450B 35-ton OBI press. Air clutch/brake. 2-1/2″ stroke; 9-3/4″ shut height. 4″ x 16″ x 30″ bolster with 4 x 10″ opening. Palm buttons. Set up for pull-backs. Bijur lube system. Ram knock-out slot.

For more information, please contact us

Two Minster OBI #4′s $48,800

(2) Minster #4 32-ton OBI stamping presses. Ideal secondary operation machines. Equipped with both dual-palm buttons and light curtains. Air clutches. One machine has 2″ stroke – the other 3″ stroke. 3″ machine is S/N 4-11508 and has 2.25″ slide adjustment. 3″ is fixed speed; 2″ is variable. Asking price is for both machines.

For more information, please contact us

Mori Seiki SL-1 CNC Lathe $5,600

Mori Seiki SL-1 CNC lathe. Swing over bed 16.5″; over carriage 6.2″ Max turning dia 4″; max length 9-1/2″. X-axis travel 3.3″; Y-axis 10.8″. X-axis rapid 157 ipm; Y-axis 315 ipm. Tailstock – taper MT #3. 8-pos turret. Spindle bore 1.57; spindle nose A2-5. Yasnac 2000GII power supply.

For more information, please contact us

Compumill $5,600

Compumill 3000 CNC knee mill model ST-N w/Dynapath 10 control having table travel of 27.5″ x 13″. Vertical quill travel of 5″ and manual knee travel of 16″. Spindle nose is NST #40. Machine is in good working condition and under power. Main Allen Bradley power switch needs repair.

For more information, please contact us

Brown & Sharpe Surface Grinder $2,900

Brown & Sharpe 618 Micromaster hyd. surface grinder. Power X-axis (5-100 fpm); Y-axis (up to 1/4″ per pass). Manual Z-axis (15″ under new wheel). Wheel 7″ x 1/2″ x 1-1/4″. 15 gallon coolant tank.

For more information, please contact us

LNS Hydrobar Model 7.76-52 Hydraulic Bar Feed $5,500

LNS Hydrobar 7.76-52 bar feed. Swiss made. Change over guide tubes in less than 1 minute. (7) feed tubes for 1-1/4″ to 3″ 12-foot bars. Tubes can be sleeved for minimum bar of 1/4″. Unit is disassembled – composed of bar unit, front and rear support stands, self-contained hydraulic unit.

For more information, please contact us

Ex-Cell-O 14″ Horizontal Optical Comparator $625

Ex-Cell-O 14″ horizontal optical comparator. Lens selection 10, 20, 31-1/4, 50, 62-1/2, 100 powers. Shadowgraph illumination. 200-watt. Manual stages measuring to tenths..

For more information, please contact us

Coe Reel ASK

Coe model CPR-4018 4,000-lb capacity coil payoff with dancer arm. Handles coils up to 18″ width by 60″ outside diameter

For more information, please contact us